Shot-peening and low-cycle fatigue of titanium alloys : instrumented indentation and X-ray diffraction / Yugang Li ; sous la direction de Manuel François et de Pascale Kanouté

Date :

Type : Livre / Book

Type : Thèse / Thesis

Langue / Language : anglais / English

Grenaillage de précontrainte

Contraintes résiduelles

Écrouissage

Titane -- Alliages

Rayons X -- Diffraction

Nanoindentation

Matériaux -- Fatigue

Classification Dewey : 620.112

François, Manuel (1962-....) (Directeur de thèse / thesis advisor)

Kanouté, Pascale (1972-....) (Directeur de thèse / thesis advisor)

Université de technologie (Troyes ; 1994-....) (Organisme de soutenance / degree-grantor)

Ecole doctorale Sciences pour l'Ingénieur (Troyes, Aube) (Ecole doctorale associée à la thèse / doctoral school)

Résumé / Abstract : Deux problèmes surviennent lorsque nous étudions les effets du grenaillage de précontrainte sur le processus de la fatigue. Le premier est la caractérisation des contraintes résiduelles (CR) et de l’écrouissage. Le second est l’évolution de CR et de l’écrouissage pendant le cyclage.Pour résoudre le premier problème, cette thèse propose une méthode pour mesurer les contraintes et l’écrouissage par nanoindentation. Ici, l’écrouissage est représenté par la déformation plastique cumulée (PP). A l’aide d’une série de simulations par éléments finis (MEF) en supposant le comportement du matériau connu, les réponses obtenues par indentation permettent d’obtenir simultanément contrainte et déformation plastique. Bien que satisfaisante d’un point vue numérique, les performances expérimentales obtenues sur un alliage de titane temps T40 restent insuffisantes. Cependant, si le profil de contrainte est connu, on peut toutefois obtenir le profil de déformation plastique. Les biais induits par la préparation de la surface ont été analysés en détail. Pour le second problème, une série d'essais de fatigue ont été effectués sur un alliage Ti-18. Quatre traitements ont été testés sur 100 cycles sous 3 amplitudes différentes de déformation. Des mesures par diffraction des rayons X ont montré que la relaxation des contraintes et l’adoucissement cyclique augmentent avec l'amplitude de déformation. Les essais d’indentation ont montré un adoucissement de la couche grenaillée

Résumé / Abstract : There are two problems when investigating the effects of shot-peening on fatigue process. The first one is characterizing residual stresses (RS) and strain hardening (WH) on the sample surface. The second one is the evolution of RS and WH during fatigue. In order to solve the first problem, this thesis proposes a “simultaneous function method” to measure RS and WH with nanoindentation. Accumulated plastic strain (PP) is used to represent WH. Then, by establishing functions of normalized indentation responses through a series of finite element method (FEM) simulations, normalized indentation responses obtained from nanoindentation experiments can be used to extract RS and PP values, assuming that the constitutive behavior is known. Although the simultaneous function method shows fairly high accuracy from a pure numerical view point, experiments performed on T40 commercial pure titanium are not completely satisfying. However, if the residual stress profile is known, the method can be used to derive the work hardening profile.In order to study the second problem, a series of strain-controlled fatigue tests are performed on Ti-18 alloy. Fatigue specimens of 4 material states, including raw, shot-peened, prestrained and prestrained + shot-peened, were tested under 3 different strain amplitudes over 100 cycles. X-ray diffraction tests on the sample surfaces showed that the RS relaxation and the cyclic softening increase together with the strain amplitude. IIT tests showed that shot-peening may induce a softening of the surface of Ti-18 alloy samples